Related Experiment Video

Updated: Jan 19, 2026

Documentation in Long-Term and Home Healthcare Setting
01:29

Documentation in Long-Term and Home Healthcare Setting

1.4K

The Shillam-Clipper Leadership Minimum Demographic Data Set: A Tool for Advancing Healthcare Research

Casey R Shillam1, Bonnie Clipper, Lola MacLean

  • 1Author Affiliations: Dean (Dr Shillam), School of Nursing, University of Portland, Oregon; Chief Clinical Officer, Wambi, Austin and Clinical Assistant Professor, Texas Tech University Health Sciences Center (Dr Clipper), El Paso, Texas; Nurse Practitioner (Dr MacLean), Providence Medical Group Family Practice, Portland, Oregon.

The Journal of Nursing Administration
|September 14, 2019
PubMed
Abstract

More Related Videos

PPE Use in Healthcare Settings I: Donning01:22

PPE Use in Healthcare Settings I: Donning

1.6K
PPE Use in Healthcare Settings II: Doffing01:10

PPE Use in Healthcare Settings II: Doffing

1.6K

Related Concept Videos

Documentation in Long-Term and Home Healthcare Setting01:29

Documentation in Long-Term and Home Healthcare Setting

Documentation in long-term care facilities and home healthcare settings is crucial for ensuring continuous, coordinated, and comprehensive care for patients. Each setting has its specific documentation processes and tools:
Long-Term Care Facilities
1.4K
PPE Use in Healthcare Settings I: Donning01:22

PPE Use in Healthcare Settings I: Donning

Donning PPE must be completed before contact with the patient. This process protects from infectious agents. The sequence and action included in each donning are critical, and the steps must be systematic to avoid exposure to pathogens. The institutional policy also needs to be followed while donning PPE. The pre-donning preparations are gathering equipment, inspecting the PPE equipment for tears, holes, or damage, removing jewelry, removing any garments below the elbows, and tying the hair...
1.6K
PPE Use in Healthcare Settings II: Doffing01:10

PPE Use in Healthcare Settings II: Doffing

The sequence of removing or doffing PPE starts with the gloves, as they are the most contaminated. Next is removal of the face shield or goggles, as they would interfere with removing other PPE. Then remove the gown, followed by the mask or respirator. Perform hand hygiene between steps if hands become contaminated and immediately after removing all PPE. Generally, the outside front and sleeves of the isolation gown, the goggles or the mask, the respirator, and the face shield are contaminated.
1.6K
Clipper Circuit01:18

Clipper Circuit

A clipper circuit is a fundamental wave-shaping device that harnesses the unique properties of diodes to alter and control waveform characteristics. This technology is widely used in electronic devices, especially in television and radar communication systems, where it enhances waveform modulation in both transmitters and receivers.
The operation of a clipper circuit can be exemplified by analyzing a dual-clipper configuration setup that integrates two ideal diodes, each paired with a biasing...
856
CorrelationCalculator and Filigree: Tools for Data-Driven Network Analysis of Metabolomics Data07:11

CorrelationCalculator and Filigree: Tools for Data-Driven Network Analysis of Metabolomics Data

We present CorrelationCalculator and Filigree, two tools for data-driven network construction and analysis of metabolomics data. CorrelationCalculator supports building a single interaction network of metabolites based on expression data, while Filigree allows building a differential network, followed by network clustering and enrichment analysis.
3.3K
Design Example: Setting a Curve Using Design Data01:09

Design Example: Setting a Curve Using Design Data

Designing and plotting a curve using field data requires precise calculations and execution. A horizontal curve with a radius of 200 meters and an intersection angle of 20 degrees is established using the method of perpendicular offsets from the long chord. The long chord, which spans between the curve's endpoints, is calculated to be 69.46 meters in length. To maintain accuracy in plotting, intervals of 3 meters are selected along the chord.The engineer determines the offset distances for each...
229