Related Experiment Video

Updated: Nov 17, 2025

Measurements of Waves in a Wind-wave Tank Under Steady and Time-varying Wind Forcing
08:54

Measurements of Waves in a Wind-wave Tank Under Steady and Time-varying Wind Forcing

Published on: February 13, 2018

8.9K

Analysis of Wind Pressure Data on Components and Cladding of Low-Rise Buildings

Dat Duthinh1, Joseph A Main1, Matthew L Gierson2

  • 1Research Structural Engineer, Engineering Laboratory, National Institute of Standards and Technology, Gaithersburg, MD 21702.

Journal of Structural Engineering (New York, N.Y.)
|February 12, 2021
PubMed
Abstract

Keywords:
ASCE 7-10Components and claddingGable roofsLow-rise buildingsWallsWind pressureWind tunnel

More Related Videos

The Measurement of Unsteady Surface Pressure Using a Remote Microphone Probe08:53

The Measurement of Unsteady Surface Pressure Using a Remote Microphone Probe

Published on: December 3, 2016

7.2K
Exploring the Effects of Atmospheric Forcings on Evaporation: Experimental Integration of the Atmospheric Boundary Layer and Shallow Subsurface13:27

Exploring the Effects of Atmospheric Forcings on Evaporation: Experimental Integration of the Atmospheric Boundary Layer and Shallow Subsurface

Published on: June 8, 2015

9.0K

Related Concept Videos

Design Example: Calculating Safe Diameter for Wind-Exposed Disc01:17

Design Example: Calculating Safe Diameter for Wind-Exposed Disc

Assessing safety in wind-exposed installations is crucial to preventing potential failures. This example explores the calculation and design adjustments needed to mount a circular disc on a building facade, where wind forces are a primary concern. A 4-meter diameter disc was initially designed as an aesthetic feature facing winds at a velocity of 25 meters per second, with an air density of 1.25 kilograms per cubic meter. Given these conditions, the drag force on the disc was determined using...
246
Fluid Pressure over Flat Plate of Constant Width01:05

Fluid Pressure over Flat Plate of Constant Width

When a body is submerged in water, it experiences fluid pressure acting normal on its surface and distributed over its area. For better design structures, it is crucial to determine the magnitude and location of the resultant force acting on the surface. In the case of a rectangular plate of constant width submerged in water, the pressure increases with depth, resulting in a linearly varying trapezoidal pressure distribution from the upper to the lower edge of the plate.
The resultant force...
2.3K
Fluid Pressure over Flat Plate of Variable Width01:02

Fluid Pressure over Flat Plate of Variable Width

When a flat plate is submerged in a fluid, the fluid exerts pressure on the plate. This pressure can lead to many different phenomena, including drag and buoyancy. To understand the behavior of the fluid over a flat plate of variable width, it is essential to analyze the distribution of the pressure exerted.
The pressure distribution on the plate can be calculated by determining the force that acts on a differential area strip of the plate. Thus, the magnitude of the force is equal to the...
1.9K
Resultant of a General Distributed Loading01:13

Resultant of a General Distributed Loading

While designing structures exposed to non-uniform loads, it is crucial to consider the resultant force and its location. This resultant force is a single vector representing the net force applied due to the distributed load.
Examples such as load distribution due to wind and load distribution on a bridge illustrate how this concept is used to analyze and design safe, reliable structures under variable loading conditions. Most structures, such as residential buildings, bridges, and towers, are...
881
Static, Stagnation, Dynamic and Total Pressure01:24

Static, Stagnation, Dynamic and Total Pressure

The concept of static, stagnation, dynamic, and total pressure is fundamental in fluid dynamics, often explained using Bernoulli's equation:
907
Fluid Pressure over Curved Plate of Constant Width01:12

Fluid Pressure over Curved Plate of Constant Width

When a curved plate of constant width is submerged in a liquid, the pressure acting normal to the plate varies continuously both in magnitude and direction. Calculating the magnitude and location of the resultant force at a point is often challenging for such cases. One of the methods to determine the resultant force and its location involves separately calculating the horizontal and vertical components of the resultant force. This complex calculation can be simplified by representing the...
1.8K