Related Experiment Video

Updated: Aug 26, 2025

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier
10:17

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier

Published on: July 12, 2017

11.6K

Nd:YAG end-pumped zigzag multi-pass slab amplifier optimization: numerical and experimental study regarding the

Mohanna Najafi, Mahdi Shayganmanesh, M Mahdi Majidof

    Optics Express
    |October 12, 2022
    PubMed

    More Related Videos

    High-speed Continuous-wave Stimulated Brillouin Scattering Spectrometer for Material Analysis07:55

    High-speed Continuous-wave Stimulated Brillouin Scattering Spectrometer for Material Analysis

    Published on: September 22, 2017

    10.2K
    Infrared Degenerate Four-wave Mixing with Upconversion Detection for Quantitative Gas Sensing10:42

    Infrared Degenerate Four-wave Mixing with Upconversion Detection for Quantitative Gas Sensing

    Published on: March 22, 2019

    6.3K

    Related Concept Videos

    Small-Signal Analysis of MOSFET Amplifiers01:23

    Small-Signal Analysis of MOSFET Amplifiers

    In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
    691
    Cascaded Op Amps01:16

    Cascaded Op Amps

    Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
    In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
    701
    MOSFET Amplifiers01:17

    MOSFET Amplifiers

    The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
    215
    Small-Signal Analysis of BJT Amplifiers01:21

    Small-Signal Analysis of BJT Amplifiers

    Small signal analysis is a fundamental approach used in electronics to understand how a Bipolar Junction Transistor (BJT) amplifier processes signals. In the active region, the BJT is designed for linear amplification. The transistor's behavior under these conditions is governed by its instantaneous base-emitter voltage VBE, a sum of the DC bias VBE, and a small AC signal VBE, resulting in the collector current iC. Here, the collector current has a DC component and an AC component.
    1.3K
    BJT Amplifiers01:14

    BJT Amplifiers

    Bipolar Junction Transistors (BJTs) are pivotal components in amplifier circuits, functioning as voltage-controlled current sources in their active region. This characteristic allows them to efficiently control the collector current through variations in the base-emitter voltage. Essentially, BJTs amplify power due to their ability to take a weak input signal and output a much stronger signal.
    In BJT amplifier configurations, particularly in common-emitter setups, the transistor's role...
    576
    Biasing of Metal-Semiconductor Junctions01:27

    Biasing of Metal-Semiconductor Junctions

    Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
    In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
    316