Related Experiment Video

Updated: Aug 7, 2025

Material Formation of Recombinant Spider Silks through Aqueous Solvation using Heat and Pressure
10:26

Material Formation of Recombinant Spider Silks through Aqueous Solvation using Heat and Pressure

Published on: May 6, 2019

5.3K

Low-bagging (growth) stretch denim yarn production by spinning optimization of cotton-wrapped dual-core elastane and

Md Abdur Rahim1, Sadikur Rahman2, Ahmed Jalal Uddin1

  • 1Department of Yarn Engineering, Bangladesh University of Textiles, Tejgaon, Dhaka, Bangladesh.

Heliyon
|March 10, 2023
PubMed

Keywords:
Bagging deformationDual-core (elastane/T400) yarnPermanent deformationSingle-core/T400 yarnSingle-core/elastane yarnStress decay

More Related Videos

Electrospinning Fundamentals: Optimizing Solution and Apparatus Parameters07:57

Electrospinning Fundamentals: Optimizing Solution and Apparatus Parameters

Published on: January 21, 2011

65.0K
Synthetic Spider Silk Production on a Laboratory Scale13:36

Synthetic Spider Silk Production on a Laboratory Scale

Published on: July 18, 2012

26.9K

Related Concept Videos

Drying Shrinkage01:21

Drying Shrinkage

When hardened concrete is exposed to air with a relative humidity of less than 100 percent, it begins to lose the free water within its capillaries. As this water evaporates, the water initially adsorbed onto the calcium silicate hydrates migrates towards these now empty spaces and eventually evaporates as well. Over time, as more water leaves, the volume of the concrete decreases, a phenomenon known as drying shrinkage.
A portion of this drying shrinkage can be reversed; if the concrete is...
114
Angle of Twist - Elastic Range01:13

Angle of Twist - Elastic Range

Consider a cylindrical shaft with a length denoted by L and a consistent cross-sectional radius referred to as r. This shaft undergoes a torque at the free end. The highest shearing strain within the shaft is directly proportional to the twist angle and the radial distance from the shaft axis. When the shaft behaves elastically, this shearing strain can be articulated using variables such as the applied torque, radial distance, the polar moment of inertia, and the modulus of rigidity. By...
367
Elastic Strain Energy for Shearing Stresses01:20

Elastic Strain Energy for Shearing Stresses

As discussed in previous lessons, strain energy in a material is the energy stored when it is elastically deformed, a concept crucial in materials science and mechanical engineering. This energy results from the internal work done against the cohesive forces within the material. When a material undergoes shearing stress and corresponding shearing strain, the strain energy density, which is the energy stored per unit volume, is calculated. Within the elastic limit, where the stress is...
241
Types of Step-Growth Polymers: Polyesters01:20

Types of Step-Growth Polymers: Polyesters

The introduction of polyesters has brought major development to the textile industry. The wrinkle-free behavior of polyester blends has eliminated the need for starching and ironing clothes.
Polyesters are commonly prepared from terephthalic acid and ethylene glycol; the crude product is known as poly(ethylene terephthalate) or PET. However, polyesters are synthesized industrially by transesterification of dimethyl terephthalate with ethylene glycol at 150 °C. The two reactants and the...
2.3K
Strain and Elastic Modulus01:15

Strain and Elastic Modulus

The quantity that describes the deformation of a body under stress is known as strain. Strain is given as a fractional change in either length, volume, or geometry under tensile, volume (also known as bulk), or shear stress, respectively, and is a dimensionless quantity. The strain experienced by a body under tensile or compressive stress is called tensile or compressive strain, respectively. In contrast, the strain experienced under bulk stress and shear stress is known as volume and shear...
4.0K
Elastic Curve from the Load Distribution01:16

Elastic Curve from the Load Distribution

The structural behavior of beams under distributed loads is critical for engineering analysis, which focuses on predicting how beams bend and react under such conditions. Different types of beams (e.g., cantilever, supported, or overhanging) behave differently under distributed load conditions.
For all beams, the analysis of the beam's reaction to distributed loads begins by understanding the relationship between a beam's load and the resulting shear forces and bending moments.
244