Related Experiment Video

Updated: Jun 28, 2025

Real-Time Proxy-Control of Re-Parameterized Peripheral Signals using a Close-Loop Interface
11:54

Real-Time Proxy-Control of Re-Parameterized Peripheral Signals using a Close-Loop Interface

Published on: May 8, 2021

4.4K

Influence of anomalous agents on the dynamics of an active system

Nikita P Kryuchkov1, Artur D Nasyrov1, Konstantin D Gursky1

  • 1Bauman Moscow State Technical University, 2nd Baumanskaya Street 5, 105005 Moscow, Russia.

Physical Review. E
|April 18, 2024
PubMed

More Related Videos

Dissociation of the Confounding Influences of Expectancy and Integrative Difficulty Residing in Anomalous Sentences in Event-related Potential Studies05:22

Dissociation of the Confounding Influences of Expectancy and Integrative Difficulty Residing in Anomalous Sentences in Event-related Potential Studies

Published on: May 9, 2019

5.4K
Controlling Flow Speeds of Microtubule-Based 3D Active Fluids Using Temperature08:04

Controlling Flow Speeds of Microtubule-Based 3D Active Fluids Using Temperature

Published on: November 26, 2019

7.2K

Related Concept Videos

Second Order systems I01:20

Second Order systems I

A servo system exemplifies a second-order system, featuring a proportional controller and load elements that ensure the output position aligns with the input position. The relationship between these components is described by a second-order differential equation. Applying the Laplace transform under zero initial conditions yields the transfer function, showing how inputs are converted to outputs in the system.
By reinterpreting the system, one can derive the closed-loop transfer function, which...
154
Second Order systems II01:18

Second Order systems II

In an underdamped second-order system, where the damping ratio ζ is between 0 and 1, a unit-step input results in a transfer function that, when transformed using the inverse Laplace method, reveals the output response. The output exhibits a damped sinusoidal oscillation, and the difference between the input and output is termed the error signal. This error signal also demonstrates damped oscillatory behavior. Eventually, as the system reaches a steady state, the error diminishes to zero.
107
Entropy Change in Reversible Processes01:10

Entropy Change in Reversible Processes

In the Carnot engine, which achieves the maximum efficiency between two reservoirs of fixed temperatures, the total change in entropy is zero. The observation can be generalized by considering any reversible cyclic process consisting of many Carnot cycles. Thus, it can be stated that the total entropy change of any ideal reversible cycle is zero.
The statement can be further generalized to prove that entropy is a state function. Take a cyclic process between any two points on a p-V diagram.
2.5K
Cyclic Processes And Isolated Systems01:19

Cyclic Processes And Isolated Systems

A thermodynamic system with zero heat exchange and work is an isolated system. For these systems, the internal energy remains constant.
In the case of a non-isolated system, the change in the internal energy is zero only if the process is cyclic. A thermodynamic process is considered cyclic if the system undergoes a series of changes and returns to its initial state. 
Consider a cyclic process that returns to its initial state, undergoing a four-step process. The heat transfer along each...
2.8K
Factors Affecting Activity Coefficient01:17

Factors Affecting Activity Coefficient

The extended Debye-Hückel equation indicates that the activity coefficient of an ion in an aqueous solution at 25°C depends on three partially interdependent properties: the ionic strength of the solution, the charge of the ion, and the ion size. 
The activity coefficient value for an ion is close to one when the solution has almost zero ionic strength, i.e., when the solution shows close to ideal behavior. As the ionic strength of the solution increases from 0 to 0.1 mol/L, a...
798
First Order Systems01:21

First Order Systems

First-order systems, such as RC circuits, are foundational in understanding dynamic systems due to their straightforward input-output relationship. Analyzing their responses to different input functions under zero initial conditions reveals significant insights into system behavior.
When a first-order system is subjected to a unit-step input, its response is characterized by its transfer function. By applying the Laplace transform of the unit-step input to the transfer function, expanding the...
90