Related Experiment Video

Updated: Jun 25, 2025

Rat Burn Model to Study Full-Thickness Cutaneous Thermal Burn and Infection
08:40

Rat Burn Model to Study Full-Thickness Cutaneous Thermal Burn and Infection

Published on: August 23, 2022

4.8K

Contact with Wet Cement-A Preventable Cause of Chemical Burn: Case Report and Discussion

Jeffrey M Levine, Nayana S Parekh, Michael L Cooper

    Advances in Skin & Wound Care
    |May 20, 2024
    PubMed
    Abstract

    More Related Videos

    A Standardized Procedure of Dressing Management for Toxic Epidermal Necrolysis07:22

    A Standardized Procedure of Dressing Management for Toxic Epidermal Necrolysis

    Published on: March 14, 2025

    288
    Burn Injury-Induced Pain and Depression-Like Behavior in Mice07:08

    Burn Injury-Induced Pain and Depression-Like Behavior in Mice

    Published on: September 29, 2021

    3.1K

    Related Concept Videos

    Burn Injuries01:22

    Burn Injuries

    Burn injuries occur when the skin and underlying tissues are damaged due to exposure to heat, electricity, chemicals, radiation, or friction. They can vary in severity, from minor superficial burns to severe deep burns that can be life-threatening.
    The damage results in the death of skin cells, which can lead to a massive loss of fluid. Dehydration, electrolyte imbalance, and renal and circulatory failure follow, which can be fatal. Burn patients are treated with intravenous fluids to offset...
    2.5K
    Acid Attack on Concrete01:21

    Acid Attack on Concrete

    When acids come into contact with concrete, they initiate a chemical reaction that dissolves the hydrated cement paste. This process leads to softening and structural weakening of the concrete. This issue is commonly observed in environments such as chimneys, sewers, and industrial settings. The severity of the damage increases as the pH of the water interacting with the concrete drops below 6.5. In particular, a pH under 4.5 can cause significant concrete damage.
    The rate at which hydrogen...
    203
    Alkali Aggregate Reaction in Concrete01:26

    Alkali Aggregate Reaction in Concrete

    The alkali-aggregate reaction in concrete involves natural siliceous minerals in aggregates reacting with alkaline hydroxides derived from cement alkalis. This reaction forms an alkali-silica gel that absorbs water, swells, and increases in volume, which is confined by the surrounding cement paste, creating internal pressures that crack and disrupt the concrete. The extent of expansion and damage can be partly attributed to the alkali-silica reaction's osmotic hydraulic pressure and the...
    93
    Handwashing II: Pre-procedure and Initial Procedure Steps01:19

    Handwashing II: Pre-procedure and Initial Procedure Steps

    The pre-procedure steps of handwashing include removing jewelry and rolling up sleeves. However, many organizations allow staff to wear wedding rings.
    The hand washing procedure itself includes the following steps. First, cover cuts, if any, on hands with a waterproof dressing. Cuts and abrasions can become contaminated with bacteria hindering the ability to clean the area thoroughly. In addition, repeated hand washing can worsen an injury.  The nails must be short and clean, without nail...
    910
    Bleeding in Fresh Concrete01:22

    Bleeding in Fresh Concrete

    Bleeding in fresh concrete occurs when water from the mix rises to the surface. This happens because the mix's solid components fail to retain all the water as they settle, leading to separation where water collects at the top. The severity of bleeding can be measured by assessing the total settlement or by noting the decrease in height per unit height of concrete.
    Bleeding can cause several issues in the concrete structure. Sometimes, the rising water gets trapped beneath large aggregate...
    119
    Hydration of Cement01:24

    Hydration of Cement

    Hydration of cement is a chemical reaction between cement particles and water. This process occurs primarily through two mechanisms: through-solution and topochemical. In the through-solution process, anhydrous compounds dissolve into their constituents, hydrates form in the solution, and then precipitate from the supersaturated solution. The topochemical process involves solid-state reactions at the cement particle surface. The through-solution process dominates the topochemical process at the...
    223