Related Experiment Video

Updated: Jun 23, 2025

Epitaxial Nanostructured α-Quartz Films on Silicon: From the Material to New Devices
11:34

Epitaxial Nanostructured α-Quartz Films on Silicon: From the Material to New Devices

Published on: October 6, 2020

5.4K

The Force-Frequency Characteristics of Quartz Wafers under a Cantilever Beam Structure

Junquan Shen1,2, Chin-Yin Chen2, Cheng-Yi Wu3

  • 1College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou 310023, China.

Sensors (Basel, Switzerland)
|June 19, 2024
PubMed

Keywords:
cantilever beamforce–frequency coefficientquartz wafers

More Related Videos

Covalent Immobilization of Proteins for the Single Molecule Force Spectroscopy11:13

Covalent Immobilization of Proteins for the Single Molecule Force Spectroscopy

Published on: August 20, 2018

11.1K
Author Spotlight: Introduction to Active Probe Atomic Force Microscopy with Quattro-Parallel Cantilever Arrays05:04

Author Spotlight: Introduction to Active Probe Atomic Force Microscopy with Quattro-Parallel Cantilever Arrays

Published on: June 13, 2023

1.5K

Related Concept Videos

Impact Loading on a Cantilever Beam01:13

Impact Loading on a Cantilever Beam

The analysis of a cantilever beam with a circular cross-section subjected to impact loading at its free end illustrates the conversion of potential energy from a dropped object into kinetic energy, which is then absorbed by the beam as strain energy. This process is crucial for understanding how materials behave under dynamic loads, which is important in fields such as construction and aerospace.
When an object is dropped onto the free end of a cantilever, its potential energy due to gravity is...
386
Shearing Stresses in a Beam: Problem Solving01:14

Shearing Stresses in a Beam: Problem Solving

A cantilever beam with a rectangular cross-section under distributed and point loads experiences shearing stresses. The analysis begins by identifying the loads acting on the beam. Then, the reactions at the beam's fixed end are calculated using equilibrium equations. The vertical reaction is a combination of the distributed and point loads, while the moment reaction is the sum of their moments. The shear force distribution along the beam, resulting from these loads, is established by...
180
Beams with Unsymmetric Loadings01:17

Beams with Unsymmetric Loadings

Analyzing a supported beam under unsymmetrical loadings is essential in structural engineering to understand how beams respond to varied force distributions. This analysis involves calculating the deflection and identifying points where the slope of the beam is zero, which are crucial for ensuring structural stability and functionality.
The first moment-area theorem determines the slope at any point on the beam. This theorem indicates that the change in slope between two points on a beam...
114
Distribution of Stresses in a Narrow Rectangular Beam01:11

Distribution of Stresses in a Narrow Rectangular Beam

In studying beam stress distribution, examining an elemental section is essential. To determine the average shearing stress on this face, the calculated shear is divided by the surface area. Importantly, shearing stresses on the beam's transverse and horizontal planes mirror each other, indicating a consistent stress distribution along the upper region of the beam. Notably, shearing stresses are absent at the beam's upper and lower surfaces due to the absence of applied forces in these...
133
Forced Oscillations01:06

Forced Oscillations

When an oscillator is forced with a periodic driving force, the motion may seem chaotic. The motions of such oscillators are known as transients. After the transients die out, the oscillator reaches a steady state, where the motion is periodic, and the displacement is determined.
6.5K
Beams with Symmetric Loadings01:15

Beams with Symmetric Loadings

The moment-area method is an analytical tool used in structural engineering to determine the slope and deflection of beams under various loads. Consider a cantilever with a concentrated load and moment at the free end. The first step is constructing a free-body diagram to calculate the reactions at the fixed end. Next, the bending moment diagram is plotted to visualize how the bending moment varies along the beam's length, focusing on points where the bending moment equals zero.
The M/EI...
186