Related Experiment Video

Updated: Jun 16, 2025

Rapid Repetition Rate Fluctuation Measurement of Soliton Crystals in a Microresonator
07:42

Rapid Repetition Rate Fluctuation Measurement of Soliton Crystals in a Microresonator

Published on: December 15, 2021

3.0K

Investigating the impact of supply voltage fluctuations on phase noise in quartz crystal oscillators

Lin Xu1, Peng Ye1, Shuang Liao2

  • 1School of Automation Engineering, University of Electronic Science and Technology of China (UESTC), No. 2006, Xiyuan Ave., West Hi-Tech Zone, 611731 Chengdu, Sichuan, China.

The Review of Scientific Instruments
|August 16, 2024
PubMed

More Related Videos

Microwave Photonics Systems Based on Whispering-gallery-mode Resonators12:18

Microwave Photonics Systems Based on Whispering-gallery-mode Resonators

Published on: August 5, 2013

16.9K
Fabrication and Testing of Microfluidic Optomechanical Oscillators09:10

Fabrication and Testing of Microfluidic Optomechanical Oscillators

Published on: May 29, 2014

12.2K

Related Concept Videos

Oscillations In An LC Circuit01:30

Oscillations In An LC Circuit

An idealized LC circuit of zero resistance can oscillate without any source of emf by shifting the energy stored in the circuit between the electric and magnetic fields. In such an LC circuit, if the capacitor contains a charge q before the switch is closed, then all the energy of the circuit is initially stored in the electric field of the capacitor. This energy is given by
2.2K
Forced Oscillations01:06

Forced Oscillations

When an oscillator is forced with a periodic driving force, the motion may seem chaotic. The motions of such oscillators are known as transients. After the transients die out, the oscillator reaches a steady state, where the motion is periodic, and the displacement is determined.
6.5K
Time and frequency -Domain Interpretation of Phase-lead Control01:24

Time and frequency -Domain Interpretation of Phase-lead Control

Phase-lead controllers are commonly used in various control systems to enhance response speed and stability. Adjusting the brightness on a television screen offers a practical example of phase-lead control. When contrast is enhanced, a phase-lead controller is employed. Mathematically, phase-lead control is identified when the first parameter is smaller than the second.
The design of phase-lead control involves the strategic placement of poles and zeros to balance steady-state error and system...
80
RLC Circuit as a Damped Oscillator01:30

RLC Circuit as a Damped Oscillator

An RLC circuit combines a resistor, inductor, and capacitor, connected in a series or parallel combination.
Consider a series RLC circuit. Here, the presence of resistance in the circuit leads to energy loss due to joule heating in the resistance. Therefore, the total electromagnetic energy in the circuit is no longer constant and decreases with time. Since the magnitude of charge, current, and potential difference continuously decreases, their oscillations are said to be damped. This is...
906
Damped Oscillations01:07

Damped Oscillations

In the real world, oscillations seldom follow true simple harmonic motion. A system that continues its motion indefinitely without losing its amplitude is termed undamped. However, friction of some sort usually dampens the motion, so it fades away or needs more force to continue. For example, a guitar string stops oscillating a few seconds after being plucked. Similarly, one must continually push a swing to keep a child swinging on a playground.
Although friction and other non-conservative...
5.7K
Time and frequency -Domain Interpretation of Phase-lag Control01:21

Time and frequency -Domain Interpretation of Phase-lag Control

Phase-lag controllers are widely used in control systems to improve stability and reduce steady-state errors. A dimmer switch controlling the brightness of a light bulb serves as a practical example of phase-lag control, gradually adjusting the bulb's brightness. Mathematically, phase-lag control or low-pass filtering is represented when the factor 'a' is less than 1.
Phase-lag controllers do not place a pole at zero, but instead influence the steady-state error by amplifying any...
87