Related Experiment Video

Updated: Jun 10, 2025

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material
07:42

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material

Published on: December 20, 2024

319

Shear Bond Strength of Five Different Repair Systems to Three Different Ceramic Materials

Martin Janda, Evaggelia Papia, Christel Larsson

    The International Journal of Prosthodontics
    |October 11, 2024
    PubMed
    Abstract

    More Related Videos

    Fused Filament Fabrication FFF of Metal-Ceramic Components08:43

    Fused Filament Fabrication FFF of Metal-Ceramic Components

    Published on: January 11, 2019

    17.2K
    An Improved Mechanical Testing Method to Assess Bone-implant Anchorage11:51

    An Improved Mechanical Testing Method to Assess Bone-implant Anchorage

    Published on: February 10, 2014

    15.5K

    Related Concept Videos

    Bonding and Strength of Aggregate01:12

    Bonding and Strength of Aggregate

    The bond between aggregate particles and the cement matrix is significantly influenced by the shape and surface texture of the aggregates. High-strength concretes benefit from a rougher texture, which leads to stronger bonding due to greater adhesion. Angular aggregates with larger surface areas also enhance this bond. The bonding quality, however, is complex to assess as no universally accepted test exists. Good bonding is indicated when a crushed concrete specimen shows some aggregate...
    140
    Mortar Properties01:17

    Mortar Properties

    Mortar properties encompass a range of characteristics crucial for construction and masonry work, including workability, water retention, bond strength, durability, compressive strength, volume change, and appearance. Workability refers to mortar's ability to be easily applied and manipulated without sagging or falling off surfaces, which is important for efficient masonry unit placement and alignment. Water retention is essential to prevent the mortar from losing moisture too quickly to...
    116
    Strength of Cement01:20

    Strength of Cement

    Strength tests for cement are not performed directly on neat cement paste due to difficulty in obtaining consistent, reliable specimens. Instead, cement is typically tested in the form of cement-sand mortar.
    For compressive strength tests, ASTM C 109-05 standards prescribe a cement-sand mix ratio of 1:2.75 and a water/cement ratio of 0.485 for making 2-inch cubes. These cubes are mixed, cast, and cured in saturated lime water at 23°C until testing. Flexural strength testing, outlined in...
    126
    Brick Masonry01:12

    Brick Masonry

    Brick masonry uses bricks as the building blocks and involves building walls from individual bricks laid in mortar. The basic building block of brick masonry is the wythe, a vertical layer of bricks with a thickness of one brick. Within a wythe, bricks can be laid in various courses or patterns, with the most common being the stretcher course, where bricks are laid with their long edge horizontal and face parallel to the wall.
    For thicker walls, multiple wythes are bonded together using...
    97
    Brick Durability, Strength, and Appearance01:15

    Brick Durability, Strength, and Appearance

    Brick durability, strength, and appearance are crucial factors in construction, influencing the choice of bricks for specific applications. The process of freeze-thaw, for instance, significantly affects brick durability. This phenomenon occurs when water absorbed by a brick expands as it freezes, potentially causing damage when it melts and refreezes. Bricks are graded for durability: SW-grade bricks are the most durable, offering high strength and low water absorption, followed by MW-grade...
    162
    Stress-Strain Diagram - Brittle Materials01:24

    Stress-Strain Diagram - Brittle Materials

    Brittle materials, including glass, cast iron, and stone, exhibit unique characteristics. They fracture without considerable change in their elongation rate, indicating that their breaking and ultimate strength are equivalent. Such materials also show lower strain levels at the point of rupture. The failure in brittle materials predominantly results from normal stresses, as evidenced by the rupture created along a surface perpendicular to the applied load. These materials do not display...
    2.2K