Related Experiment Video

Updated: Aug 8, 2026

A Two-interval Forced-choice Task for Multisensory Comparisons
07:13

A Two-interval Forced-choice Task for Multisensory Comparisons

Published on: November 9, 2018

The intelligibility of whitened and amplitude compressed speech in a multitalker background

L L Young, J T Goodman, R Carhart

    Journal of Speech and Hearing Research
    |June 1, 1980
    PubMed

    More Related Videos

    Foreign Accent and Forensic Speaker Identification in Voice Lineups: The Influence of Acoustic Features Based on Prosody09:09

    Foreign Accent and Forensic Speaker Identification in Voice Lineups: The Influence of Acoustic Features Based on Prosody

    Published on: September 27, 2024

    Memorization-Based Training and Testing Paradigm for Robust Vocal Identity Recognition in Expressive Speech Using Event-Related Potentials Analysis05:48

    Memorization-Based Training and Testing Paradigm for Robust Vocal Identity Recognition in Expressive Speech Using Event-Related Potentials Analysis

    Published on: August 9, 2024

    Related Concept Videos

    ¹H NMR: Interpreting Distorted and Overlapping Signals01:02

    ¹H NMR: Interpreting Distorted and Overlapping Signals

    Spin systems where the difference in chemical shifts of the coupled nuclei is greater than ten times J are called first-order spin systems. These nuclei are weakly coupled, and their chemical shifts and coupling constant can generally be estimated from the well-separated signals in the spectrum.
    As Δν decreases and the signals move closer, the doublets appear increasingly distorted. The intensities of the inner lines increase at the cost of those of the outer lines as the signals are slanted or...
    Sound Intensity Level00:53

    Sound Intensity Level

    Humans perceive sound by hearing. The human ear helps sound waves reach the brain, which then interprets the waves and creates the perception of hearing. The loudness of the environment in which a person is located determines whether they can distinguish between different sound sources.
    The human ear can perceive an extensive range of sound intensity, necessitating the use of the logarithmic scale to define a physical quantity—the intensity level. It is a ratio of two intensities and hence a...
    Sound Waves: Interference00:53

    Sound Waves: Interference

    Sound waves can be modeled either as longitudinal waves, wherein the molecules of the medium oscillate around an equilibrium position, or as pressure waves. When two identical waves from the same source superimpose on each other, the combination of two crests or two troughs results in amplitude reinforcement known as constructive interference. If two identical waves, that are initially in phase, become out of phase because of different path lengths, the combination of crests with troughs...
    Difference from Background: Limit of Detection01:05

    Difference from Background: Limit of Detection

    The limit of detection (LOD) is the smallest amount of analyte that can be distinguished from the background noise. The LOD value corresponds to the concentration at which the analyte signal is three times larger than the standard deviation of the blank signal. Below this value, the analyte signal cannot be differentiated from the background noise. It is calculated by dividing the calibration slope by 3 times the standard deviation of the blank signals.
    The LOD indicates the presence or absence...
    Interference: Path Lengths01:10

    Interference: Path Lengths

    Consider two sources of sound, that may or may not be in phase, emitting waves at a single frequency, and consider the frequencies to be the same.
    Two special sources may be considered when they are in phase. This can be easily achieved by feeding the two sources from the same source. An example would be synchronizing the two speakers by feeding them with the same source, such as the sound waves produced by a tuning fork. This setup ensures that the two sources have the same frequency and are...
    Reconstruction of Signal using Interpolation01:10

    Reconstruction of Signal using Interpolation

    Signal processing techniques are essential for accurately converting continuous signals to digital formats and vice versa. When a continuous signal is sampled with a period T, the resulting sampled signal exhibits replicas of the original spectrum in the frequency domain, spaced at intervals equal to the sampling frequency. To handle this sampled signal, a zero-order hold method can be applied, which creates a piecewise constant signal by retaining each sample's value until the next sampling...