Related Experiment Video

Updated: Mar 29, 2026

Induction of Microstreaming by Nonspherical Bubble Oscillations in an Acoustic Levitation System
08:19

Induction of Microstreaming by Nonspherical Bubble Oscillations in an Acoustic Levitation System

Published on: May 9, 2021

2.9K

"Large" Tank Acoustics: How Big Is Big Enough?

Michael D Gray1, Peter H Rogers2, Arthur N Popper3

  • 1Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA, 30332, USA. michael.gray@me.gatech.edu.

Advances in Experimental Medicine and Biology
|November 28, 2015
PubMed

Keywords:
Acoustic pressureHearingParticle velocity

More Related Videos

Studying Cavitation Enhanced Therapy07:36

Studying Cavitation Enhanced Therapy

Published on: April 9, 2021

6.0K
Exploring the Effects of Atmospheric Forcings on Evaporation: Experimental Integration of the Atmospheric Boundary Layer and Shallow Subsurface13:27

Exploring the Effects of Atmospheric Forcings on Evaporation: Experimental Integration of the Atmospheric Boundary Layer and Shallow Subsurface

Published on: June 8, 2015

9.3K

Related Concept Videos

Sound Waves: Resonance01:14

Sound Waves: Resonance

Resonance is produced depending on the boundary conditions imposed on a wave. Resonance can be produced in a string under tension with symmetrical boundary conditions (i.e., has a node at each end). A node is defined as a fixed point where the string does not move. The symmetrical boundary conditions result in some frequencies resonating and producing standing waves, while other frequencies interfere destructively. Sound waves can resonate in a hollow tube, and the frequencies of the sound...
3.7K
Echo01:06

Echo

The human ear cannot distinguish between two sources of sound if they happen to reach within a specific time interval, typically 0.1 seconds apart. More than this, and they are perceived as separate sources.
Imagine the sound is reflected back to the ears. Assuming that the source is very close to the human, the difference between hearing the two sounds—the emitted sound and the reflected sound—may be more than the minimum time for perceiving distinct sounds. If this is the case,...
1.1K
Design Example: Vintage Mixing Console01:17

Design Example: Vintage Mixing Console

A sound engineer at a music company recently encountered a problem. The output from their newly acquired studio's vintage mixing console was too low for the requirements of modern recording equipment. To rectify this situation, the engineer decided to design an audio pre-amplifier using an operational amplifier (op-amp) to boost the signal level.
The specifications for the pre-amplifier were clear. It needed to amplify the audio signal by a factor of 10, have an input impedance above 10...
654
Standing Waves in a Cavity01:28

Standing Waves in a Cavity

A household microwave and lasers are examples of standing electromagnetic waves in a cavity. When two conducting metal plates are placed parallel at the nodal planes, it creates a cavity where standing waves are formed. The cavity between the two planes is analogous to a stretched string held at the points x = 0 and x = L. Here, the distance 'L' between the two planes must be an integer multiple of half of the wavelength. The wavelengths that satisfy this condition are given by:
1.6K
Deriving the Speed of Sound in a Liquid01:09

Deriving the Speed of Sound in a Liquid

As with waves on a string, the speed of sound or a mechanical wave in a fluid depends on the fluid's elastic modulus and inertia. The two relevant physical quantities are the bulk modulus and the density of the material. Indeed, it turns out that the relationship between speed and the bulk modulus and density in fluids is the same as that between the speed and the Young's modulus and density in solids.
The speed of sound in fluids can be derived by considering a mechanical wave...
1.1K
Problem Solving: Volume01:13

Problem Solving: Volume

The volume of a fuel tank mounted on the wing of a jet aircraft can be modeled using the concept of solids of revolution. In this case, the tank is formed by rotating a two-dimensional region, defined by a mathematical function, about the x-axis. The region extends along the axis from zero to two meters, and the resulting three-dimensional shape is symmetric about the axis of rotation. Because the boundary curve lies directly against the axis, the disk method is an appropriate technique for...
202