Related Experiment Video

Updated: Feb 3, 2026

3D Printing - Evaluating Particle Emissions of a 3D Printing Pen
06:44

3D Printing - Evaluating Particle Emissions of a 3D Printing Pen

Published on: October 9, 2020

9.1K

Imaging Factors Impacting on Accuracy and Radiation Dose in 3D Printing

Jorge Javier de Lima Moreno1, Gabriela Salatino Liedke2, Roberto Soler1

  • 11Department of Maxillofacial Prosthesis, School of Dentistry, Universidad de la Republica, Las Heras 1925, Montevideo, Uruguay.

Journal of Maxillofacial and Oral Surgery
|October 23, 2018
PubMed
Abstract

Keywords:
3D printingCone beam computed tomographyMultidetector computed tomographyRadiation dosage

More Related Videos

Author Spotlight: Real-Time Imaging of Bonding in 3D-Printed Layers04:36

Author Spotlight: Real-Time Imaging of Bonding in 3D-Printed Layers

Published on: September 1, 2023

3.9K
Low-Dose Gamma Radiation Sterilization for Decellularized Tracheal Grafts08:17

Low-Dose Gamma Radiation Sterilization for Decellularized Tracheal Grafts

Published on: April 14, 2023

1.2K

Related Concept Videos

Biological Effects of Radiation02:59

Biological Effects of Radiation

All radioactive nuclides emit high-energy particles or electromagnetic waves. When this radiation encounters living cells, it can cause heating, break chemical bonds, or ionize molecules. The most serious biological damage results when these radioactive emissions fragment or ionize molecules. For example, α and β particles emitted from nuclear decay reactions possess much higher energies than ordinary chemical bond energies. When these particles strike and penetrate matter, they...
17.9K
Improving Translational Accuracy02:07

Improving Translational Accuracy

Base complementarity between the three base pairs of mRNA codon and the tRNA anticodon is not a failsafe mechanism. Inaccuracies can range from a single mismatch to no correct base pairing at all. The free energy difference between the correct and nearly correct base pairs can be as small as 3 kcal/ mol. With complementarity being the only proofreading step, the estimated error frequency would be one wrong amino acid in every 100 amino acids incorporated. However, error frequencies observed in...
14.9K
Improving Translational Accuracy02:07

Improving Translational Accuracy

3.7K
Uncertainty in Measurement: Accuracy and Precision03:37

Uncertainty in Measurement: Accuracy and Precision

Scientists typically make repeated measurements of a quantity to ensure the quality of their findings and to evaluate both the precision and the accuracy of their results. Measurements are said to be precise if they yield very similar results when repeated in the same manner. A measurement is considered accurate if it yields a result that is very close to the true or the accepted value. Precise values agree with each other; accurate values agree with a true value. 
101.2K
Accuracy and Precision01:52

Accuracy and Precision

Scientists typically make repeated measurements of a quantity to ensure the quality of their findings and to evaluate both the precision and the accuracy of their results. Measurements are said to be precise if they yield very similar results when repeated in the same manner. A measurement is considered accurate if it yields a result that is very close to the true or the accepted value. Precise values agree with each other; accurate values agree with a true value.  Highly accurate...
15.3K
Radiation: Applications01:17

Radiation: Applications

The average temperature of Earth is the subject of much current discussion. Earth is in radiative contact with both the Sun and dark space; it receives almost all its energy from the radiation of the Sun and reflects some of it into outer space. Dark space is very cold, about 3 K, so Earth radiates energy into it. For instance, heat transfer occurs from soil and grasses, the rate of which can be so rapid that frost can occur on clear summer evenings, even in warm latitudes.
The average...
1.8K