Related Experiment Video

Updated: Feb 3, 2026

Extraction of Organochlorine Pesticides from Plastic Pellets and Plastic Type Analysis
10:12

Extraction of Organochlorine Pesticides from Plastic Pellets and Plastic Type Analysis

Published on: July 1, 2017

12.2K

Synthesis and Plasticization Performance of Reactive Plasticizers Utilizing Catalyst-Free Azide-Alkyne Click Reaction

Yechen Shen1, Younghwan Kwon1

  • 1Department of Chemical Engineering, Daegu University, Gyeongsan, Gyeongbuk 38453, Korea.

Journal of Nanoscience and Nanotechnology
|October 27, 2018
PubMed

More Related Videos

Forming Micro-and Nano-Plastics from Agricultural Plastic Films for Employment in Fundamental Research Studies08:21

Forming Micro-and Nano-Plastics from Agricultural Plastic Films for Employment in Fundamental Research Studies

Published on: July 27, 2022

4.8K
Efficient and Site-specific Antibody Labeling by Strain-promoted Azide-alkyne Cycloaddition09:06

Efficient and Site-specific Antibody Labeling by Strain-promoted Azide-alkyne Cycloaddition

Published on: December 23, 2016

22.3K

Related Concept Videos

Plasticity00:58

Plasticity

Plasticity is the property where an object loses its elasticity and undergoes irreversible deformation, even after the deformation forces are eliminated. If a material deforms irreversibly without increasing stress or load, then this is called ideal plasticity. For example, when a force is applied to an aluminum rod, it changes its shape, but it does not return to its original shape once the force is removed. Plastic deformation or ductility is thus a permanent deformation or change in the...
3.1K
Plasticizers01:31

Plasticizers

Water-reducers, or plasticizers, are chemical admixtures used in concrete to improve strength and workability. These additives reduce the water-cement ratio without compromising workability, lower the cement content while maintaining the same workability, or increase workability to assist concrete placement in inaccessible areas.
Plasticizers function by using surface-active agents to create repulsive electrostatic forces between cement particles. This dispersion enhances the concrete's...
368
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
579
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
444
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
465
Plastic Deformation in Circular Shafts01:20

Plastic Deformation in Circular Shafts

When materials are subjected to forces that surpass their yield strength, they undergo a process known as plastic deformation. This results in a permanent alteration or strain in their structure. This concept can be specifically applied to circular shafts, where the deformation leads to a change in its shape. The precise evaluation of this plastic deformation requires understanding the stress distribution within the circular shaft, which is achieved by calculating the maximum shearing stress in...
480