Related Experiment Video

Updated: Dec 26, 2025

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material
07:42

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material

Published on: December 20, 2024

654

Torque Maintenance Capacity, Vertical Misfit, Load to Failure, and Stress Concentration of Zirconia Restorations

Dario Adolfi, João Paulo Mendes Tribst, Alexandre Luiz Souto Borges

    The International Journal of Oral & Maxillofacial Implants
    |March 7, 2020
    PubMed
    Abstract

    More Related Videos

    Oral Biofilm Formation on Different Materials for Dental Implants11:19

    Oral Biofilm Formation on Different Materials for Dental Implants

    Published on: June 24, 2018

    12.0K
    An Improved Mechanical Testing Method to Assess Bone-implant Anchorage11:51

    An Improved Mechanical Testing Method to Assess Bone-implant Anchorage

    Published on: February 10, 2014

    15.8K

    Related Concept Videos

    Residual Stresses in Circular Shafts01:10

    Residual Stresses in Circular Shafts

    In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the...
    447
    Stress Concentrations in Circular Shafts01:18

    Stress Concentrations in Circular Shafts

    Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
    452
    Circular Shafts - Elastoplastic Materials01:24

    Circular Shafts - Elastoplastic Materials

    The study of solid circular shafts under stress shows that within the elastic limit, stress increases directly to the distance from the shaft's center. This relationship holds until the shaft reaches a critical point of stress, beyond which it begins to yield, marking the transition from elastic to plastic deformation. At this crucial juncture, the maximum torque the shaft can endure without permanent deformation is determined, signifying the limit of its elastic behavior.
    As torque on the...
    373
    Design of Transmission Shafts - Stress Analysis01:15

    Design of Transmission Shafts - Stress Analysis

    Designing a transmission shaft requires a thorough understanding of the stresses induced by bending moments and torques, especially in systems where power is transferred through gears. These forces create force-couple systems at the centers of the shaft's cross-sections, leading to both transverse and torsional loading. Although shearing stresses from transverse loads are typically smaller than those from torques and are often overlooked, the significant normal stresses from these loads...
    678
    Stresses under Combined Loadings01:23

    Stresses under Combined Loadings

    When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
    The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
    392
    Residual Stresses01:26

    Residual Stresses

    Residual stresses reside in a structure even after removing the original stress inducer. This phenomenon often arises from varied plastic deformations across different parts of a structure. Consider a rod stretched beyond its yield point. It will not regain its original length due to permanent deformation. Even after load removal, the rod does not entirely lose stress because of uneven plastic deformations, resulting in residual stresses. The computation of these stresses in structures is...
    498