Related Experiment Video

Updated: Dec 7, 2025

Nanofabrication of Gate-defined GaAs/AlGaAs Lateral Quantum Dots
15:47

Nanofabrication of Gate-defined GaAs/AlGaAs Lateral Quantum Dots

Published on: November 1, 2013

16.8K

Circuit Simulation Considering Electrical Coupling in Monolithic 3D Logics with Junctionless FETs

Tae Jun Ahn1,2, Yun Seop Yu1

  • 1Department of Electrical, Electronic and Control Engineering and IITC, Hankyong National University, 327 Jungang-ro, Anseong-si, Gyenggi-do 17579, Korea.

Micromachines
|September 29, 2020
PubMed

Keywords:
JLFETcircuit simulationelectrical couplingjunctionless FETmonolithic 3D integrated circuit (IC)parameter extraction

More Related Videos

Scalable Quantum Integrated Circuits on Superconducting Two-Dimensional Electron Gas Platform05:39

Scalable Quantum Integrated Circuits on Superconducting Two-Dimensional Electron Gas Platform

Published on: August 2, 2019

10.1K
Rapid Development of Cell State Identification Circuits with Poly-Transfection09:21

Rapid Development of Cell State Identification Circuits with Poly-Transfection

Published on: February 24, 2023

1.9K

Related Concept Videos

Biasing of FET01:22

Biasing of FET

Biasing a Junction Field Effect Transistor (JFET) is crucial for setting operational parameters and ensuring efficient functioning in electronic circuits. JFETs are characterized by using a single carrier type in N-channel or P-channel configurations, where the channel is surrounded by PN junctions. These junctions are central to the device's ability to control current flow.
In an N-channel JFET, the structure consists of N-type material forming the channel on a P-type substrate, with the...
546
Biasing of Metal-Semiconductor Junctions01:27

Biasing of Metal-Semiconductor Junctions

Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
455
Second-Order Circuits01:17

Second-Order Circuits

Integrating two fundamental energy storage elements in electrical circuits results in second-order circuits, encompassing RLC circuits and circuits with dual capacitors or inductors (RC and RL circuits). Second-order circuits are identified by second-order differential equations that link input and output signals.
Input signals typically originate from voltage or current sources, with the output often representing voltage across the capacitor and/or current through the inductor. For example, in...
3.0K
First-Order Circuits01:15

First-Order Circuits

First-order electrical circuits, which comprise resistors and a single energy storage element - either a capacitor or an inductor, are fundamental to many electronic systems. These circuits are governed by a first-order differential equation that describes the relationship between input and output signals.
One common example of a first-order circuit is the RC (resistor-capacitor) circuit. These circuits are used in relaxation oscillators such as neon lamp oscillator circuits. When voltage is...
3.1K
Metal-Semiconductor Junctions01:24

Metal-Semiconductor Junctions

The contact of metal and semiconductor can lead to the formation of a junction with either Schottky or Ohmic behavior.
Schottky Barriers
Schottky barriers arise when a metal with a work function (Φm) contacts a semiconductor with a different work function (Φs). Initially, electrons transfer until the Fermi levels of the metal and semiconductor align at equilibrium. For instance, if Φm > Φs, the semiconductor Fermi level is higher than the metal's before contact. The...
738
Small-Signal Analysis of MOSFET Amplifiers01:23

Small-Signal Analysis of MOSFET Amplifiers

In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
944