Related Experiment Video

Updated: Aug 9, 2026

Mechanical Stimulation of Chondrocyte-agarose Hydrogels
12:45

Mechanical Stimulation of Chondrocyte-agarose Hydrogels

Published on: October 27, 2012

Stress-sharing between the fluid and solid components of articular cartilage under varying rates of compression

A Oloyede1, N Broom

  • 1Department of Mechanical Engineering, School of Engineering, University of Auckland, New Zealand.

Connective Tissue Research
|January 1, 1993
PubMed

More Related Videos

An Experimental and Finite Element Protocol to Investigate the Transport of Neutral and Charged Solutes across Articular Cartilage07:57

An Experimental and Finite Element Protocol to Investigate the Transport of Neutral and Charged Solutes across Articular Cartilage

Published on: April 23, 2017

Biotribological Testing and Analysis of Articular Cartilage Sliding against Metal for Implants09:08

Biotribological Testing and Analysis of Articular Cartilage Sliding against Metal for Implants

Published on: May 14, 2020

Related Concept Videos

Shearing Stress01:18

Shearing Stress

Shearing stress, denoted by the Greek letter tau (τ), is stress caused by forces acting transversely on an object. These forces create internal ones within the entity in the plane where the external forces are applied. The resultant of these internal forces is the shear in the section.
The average shearing stress can be calculated by dividing the shear by the area of the cross-section.
Shearing Strain01:20

Shearing Strain

The shearing strain represents a cubic element's angular change when subjected to shearing stress. This type of stress can transform a cube into an oblique parallelepiped without influencing normal strains. The cubic element experiences a significant transformation when exposed solely to shearing stress. Its shape alters from a perfect cube into a rhomboid, clearly demonstrating the effect of shearing strain. The degree of this strain is considered positive if it reduces the angle between the...
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
Design Example: Deciding Thickness of Lubricating Fluid in a Shaft01:23

Design Example: Deciding Thickness of Lubricating Fluid in a Shaft

Effective lubrication between a rotating shaft and its bearing housing is essential in rotating machinery to minimize friction, wear, and energy loss. With carefully controlled thickness and viscosity, the lubricant layer prevents metal-to-metal contact, ensuring smooth operation.
To calculate the required thickness of the lubricant layer, the tangential velocity at the shaft's surface must first be determined. This velocity is calculated by converting the rotational speed to angular velocity...