Related Experiment Video

Updated: Dec 2, 2025

Generation and Coherent Control of Pulsed Quantum Frequency Combs
06:42

Generation and Coherent Control of Pulsed Quantum Frequency Combs

Published on: June 8, 2018

9.5K

A radiofrequency voltage-controlled current source for quantum spin manipulation

D S Barker1, A Restelli1, J A Fedchak2

  • 1Joint Quantum Institute, University of Maryland and National Institute of Standards and Technology, College Park, Maryland 20742, USA.

The Review of Scientific Instruments
|November 3, 2020
PubMed
Abstract

More Related Videos

Gradient Echo Quantum Memory in Warm Atomic Vapor10:00

Gradient Echo Quantum Memory in Warm Atomic Vapor

Published on: November 11, 2013

13.1K
Silicon Metal-oxide-semiconductor Quantum Dots for Single-electron Pumping14:58

Silicon Metal-oxide-semiconductor Quantum Dots for Single-electron Pumping

Published on: June 3, 2015

15.2K

Related Concept Videos

Force On A Current Loop In A Magnetic Field01:17

Force On A Current Loop In A Magnetic Field

Magnetic forces on wires carrying current are most frequently applied in motors. A DC motor is a device that converts electrical energy into mechanical work. In motors, wire loops are enclosed in a magnetic field. When current flows through the loops, the magnetic field applies torque, which causes the shaft to rotate. The direction of the current is reversed once the loop's surface area is lined up with the magnetic field, causing a constant torque on the loop. During the process, commutators...
3.8K
Spin–Spin Coupling Constant: Overview01:08

Spin–Spin Coupling Constant: Overview

In bromoethane, the three methyl protons are coupled to the two methylene protons that are three bonds away. In accordance with the n+1 rule, the signal from the methyl protons is split into three peaks with 1:2:1 relative intensities. The methylene protons appear as a quartet, with the relative intensities of 1:3:3:1.
Qualitatively, any spin plus-half nucleus polarizes the spins of its electrons to the minus-half state. Consequently, the paired electron in the hydrogen–carbon bond must...
1.2K
Torque On A Current Loop In A Magnetic Field01:13

Torque On A Current Loop In A Magnetic Field

The most common application of magnetic force on current-carrying wires is in electric motors. These consist of loops of wire, which are placed between the magnets with a magnetic field. When current flows through the loops, the magnetic field applies torque, which causes the shaft to rotate, thus converting electrical energy to mechanical energy.
Consider a rectangular current-carrying loop containing N turns of wire, placed in a uniform magnetic field. The net force on a current-carrying loop...
5.4K
RC Circuit with Source01:15

RC Circuit with Source

When a DC source is abruptly applied to an RC (Resistor-Capacitor) circuit, the voltage can be represented as a unit step function. The voltage across the capacitor, known as the step response, characterizes how the circuit reacts to this sudden change in input.
Due to the inherent properties of a capacitor, its voltage cannot change instantaneously. This means that immediately after the switch is closed, the capacitor's voltage remains the same as it was just before the switch was closed.
2.3K
Controlled-Current Coulometry: Overview01:27

Controlled-Current Coulometry: Overview

Controlled current coulometry, also known as amperostatic coulometry, is a technique used in electrochemical analysis to measure the quantity of a substance through the controlled passage of current. It involves the application of a constant current to an electrochemical cell containing the analyte of interest. As the current flows through the cell, the analyte undergoes a redox reaction at the electrode surface, resulting in a charge transfer. By monitoring the time required for a certain...
499
RC Circuit without Source01:16

RC Circuit without Source

When a DC source is abruptly disconnected from an RC (Resistor-Capacitor) circuit, the circuit becomes source-free. Assuming that the capacitor was fully charged before the source was removed, its initial voltage, denoted as V0, can be considered as the initial energy that stimulates the circuit.
Applying Kirchhoff's current law at the top node of the circuit and substituting the current values across the components, a first-order differential equation is obtained. By rearranging the terms...
2.1K