Related Experiment Video

Updated: Jan 3, 2026

Silicon Metal-oxide-semiconductor Quantum Dots for Single-electron Pumping
14:58

Silicon Metal-oxide-semiconductor Quantum Dots for Single-electron Pumping

Published on: June 3, 2015

15.3K

Integrated Cold-Start of a Boost Converter at 57mV using Cross-Coupled Complementary Charge Pumps and

Soumya Bose1, Tejasvi Anand1, Matthew L Johnston1

  • 1School of Electrical Engineering and Computer Science, Oregon State University, Corvallis, OR, 97331, USA.

IEEE Journal of Solid-State Circuits
|November 15, 2019
PubMed

Keywords:
DC-DC converterThermoelectric energy harvestingcharge pumpintegrated cold-startring oscillator

More Related Videos

In Situ Transmission Electron Microscopy with Biasing and Fabrication of Asymmetric Crossbars Based on Mixed-Phased a-VOx09:49

In Situ Transmission Electron Microscopy with Biasing and Fabrication of Asymmetric Crossbars Based on Mixed-Phased a-VOx

Published on: May 13, 2020

4.3K
Scalable Quantum Integrated Circuits on Superconducting Two-Dimensional Electron Gas Platform05:39

Scalable Quantum Integrated Circuits on Superconducting Two-Dimensional Electron Gas Platform

Published on: August 2, 2019

10.2K

Related Concept Videos

MOSFET: Enhancement Mode01:22

MOSFET: Enhancement Mode

Enhancement-mode MOSFETs are pivotal components in electronics, distinguished by their capacity to act as highly efficient switches. They are part of the larger family of metal-oxide Semiconductor Field-Effect Transistors (MOSFETs). They are available in two types: p-channel and n-channel, each tailored to specific polarity operations.
In their basic form, enhancement-mode MOSFETs are typically non-conductive when the gate-source voltage (Vgs) is zero. This default 'off' state means no...
723
Voltage Doubler Circuit01:23

Voltage Doubler Circuit

A voltage doubler circuit integrates two main components: a clamping section and a rectifier section. The clamping section consists of a capacitor (C1) and a diode (D1), whereas the rectifier section is equipped with another diode (D2) and capacitor (C2). This circuit produces an output voltage with twice the amplitude of the sinusoidal input voltage.
1.5K
RC Circuits: Charging A Capacitor01:30

RC Circuits: Charging A Capacitor

A circuit containing resistance and capacitance is called an RC circuit. A capacitor is an electrical component that stores electric charge by storing energy in an electric field. Consider a simple RC circuit having a DC (direct current) voltage source ε, a resistor R, a capacitor C, and a two-way position switch. In the circuit, the capacitor can be charged or discharged depending on the position of the switch.
When the switch is moved to connect the battery, the circuit reduces to a simple...
4.4K
Design Example: Capacitance Multiplier Circuit01:20

Design Example: Capacitance Multiplier Circuit

In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
1.4K
MOSFET Amplifiers01:17

MOSFET Amplifiers

The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
436
Half wave rectifier01:20

Half wave rectifier

A half-wave rectifier is a fundamental circuit in electronics, designed to convert alternating current (AC) voltage into a unidirectional voltage. It utilizes the simplest form of diode rectification, where the circuit comprises a single diode in series with a load resistor and an AC power source.
2.3K